memory port
英 [ˈmeməri pɔːt]
美 [ˈmeməri pɔːrt]
网络 存储器出入口
双语例句
- Before the advent of USB ports, in order to connect different devices such as a printer, a flash memory, or a removable hard drive, to the computer, the computer required the existence of the different port types.
在USB端口出现之前，为了将各种不同的设备（例如打印机、闪存或移动硬盘）连接到计算机，计算机需要具备不同的端口类型。 - The memory card port is in the console instead, freeing up massive space and stripping out size and weight requirements.
取而代之的是在主机上设置两个记忆卡插槽，这样做便可以节约大量的空间，缩小手柄的体积，以及减轻总体重量。 - I want to open the treasure box of the memory port, diligent seek, work hard to see, to the feeling the natural affection and the friendship that I own.
我要打开记忆的宝盒，努力的寻找，用心去看，去感悟我所拥有的亲情和友情。 - Memory Port of the Common Oscp Controlled by 8098 SCP
8098单片机控制的普通示波器存储接口 - Taking PCI bus sample card design as a reference, author discusses some key techniques in programming the WDM driver such as memory mapping, the accessing to I/ O port, the requesting for interrupt and the communication between application and driver.
结合皮秒时间相关单光子计数光谱仪的PCI总线数据采集卡设计，对驱动程序设计过程中的关键技术如存储器映射、I/O访问、中断请求、驱动程序与应用程序间的通信等做了讨论。 - Its application program is written into user memory by RS232 string port, which can ensure no dropout when power is suddenly shut down.
应用程序由RS232串口写入用户存储器，确保电源消失后程序不会造成任何丢失； - The memory spaces configuration, synchronous serial interface ( SSI), serial communications interface ( SCI), host port of the DSP system are summarized.
概述了DSP系统的存储器空间设置、同步串行接口、串行通讯接口、主接口的特点； - The article first introduces the features of the PCMCIA port and discusses about the Memory and IO working mode of the port.
本文首先介绍了PCMCIA接口的特点，对此接口的Memory和IO两种工作方式进行了讨论。 - Driver Works are regarded as the developing instrument, WDM device driver is developed based on PCI local bus. Such driver can access the configuration space, physical memory and I/ O port of the PCI device and realize the interrupt service routine.
以DriverWorks为开发工具开发基于PCI局部总线的设备驱动程序，实现了可以访问PCI设备配置空间、物理内存、I/O端口及实现中断服务程序的PCI设备WDM驱动程序。 - On the hardware platform, the application software is designed. They include system initialization, ADC sampling, high-voltage control, peak detecting, CAN communication, online programming for EEPROM ( Electrically Erasable Programmable Read Only Memory) through serial port, and writing and reading.
在硬件设计完成的基础上，进行了系统的应用软件设计，分别完成了系统初始化程序、A／D采样程序、高压控制程序、峰值检测程序、CAN通信程序以及串行EEPROM在线编程及读写程序。 - The paper introduced FDU ID memory of 408 seismograph and a device using a bi-directional parallel port for printer on a personal computer to read/ write FDU EEPROM chip.
本文介绍408地震仪FDU标识号存储器及一款利用个人计算机双向并行打印口读写FDUEEPROM芯片的装置。 - It defines three sub problems for memory mapping, i.e. port mapping, bit width mapping and word mapping and finally combines those solutions into an efficient memory mapping algorithm.
定义存储器的映射为端口映射、字长映射和字数映射，最后把这3个子问题综合起来形成完整的算法。 - In this paper, it discuss the hardware design and software design of the system. In hardware design, it mainly includes peripheral memory, low Butterworth filter, isolated serial port.
在论文中讨论了系统的硬件设计和软件设计：硬件设计包括外围存储器的扩展、巴特沃斯虑波器的设计、防干扰的隔离串口的设计等； - The key factors on the time interleaving design are interleaving speed, circuit area and memory unit. The paper adopts one port SRAM to implement the design in order to use less memory and the optimization design methods to improve the circuit area.
时间解交织器的交织速度、电路面积、占用内存、是设计中主要因素，文中采用了单口SRAM实现，减少了对存储器的使用，利用IC设计的优化设计方法来改善电路的面积。 - Design for Share Memory Circuit with Multiple Port
多端口共享存贮器电路设计 - In the interactive mode, the commands allow the processor to read/ modify memory areas, set environment variables, download data from the serial port or from the Ethernet interface and execute code routines.
在其交互模式下使用有关命令可以进行对存储区进行读取和修改、设置环境变量、通过串口或以太网接口下载并执行常规代码等操作。 - Its basic utilization method and application of DLL technique is introduced in Windows programming, and shows all source coders of two practical DLL about internal memory access and port I/ O.
介绍DLL技术在Windows编程中的基本运用方法及应用实例，给出了直接内存访问及端口I/O的两个实用DLL的全部源代码。 - In view of the DSP memory space features and the insufficient I/ O port features, this paper extends the DSP memory and the I/ O port.
针对DSP存储空间及其I/O口不足的特点，对DSP的存储器及其I/O口进行了扩展。 - This design uses two-port Random Access Memory ( RAM) in FPGA as data buffer, so it is very convenient because PCI-E bus and local bus can accesses it though respective port.
为了增加系统的灵活性，在FPGA中设计了双端口随机存储器（RAM）作为数据的缓存区，PCI-E总线和本地总线可以通过各自的接口对其独立的访问。 - In this paper, a new type of downhole memory gauge using USB interface is discussed. It can replace the traditional RS-232 serial port.
本文将USB接口用于存储式测井仪器，取代了传统的RS-232串口。 - By using memory plot 、 serial port communication etc, the software system has a better visualization and flexible expansibility character.
软件使用了内存画布、串口通讯等技术，有效的实现了动力定位操控功能和状态监视功能。